Hangar Door Repair Guide

Most hangar door repairs come down to one worn part. A seal that has hardened, a caster bearing that has seized, a limit switch that has stopped reading. Find the symptom below, match it to the part, and get your door working again.

Hangar Door Parts supplies repair and replacement parts for aircraft hangar doors and any other bifold, rolling or hydraulic hangar door, from any manufacturer. We do not send out repair crews. What we do is help you or your technician identify the right part, ship it, and talk you through what you are looking at over the phone.

Not sure which part failed?
Call with your door type and a description of the problem. Monday to Friday, 8:00 AM to 5:00 PM Eastern.

Call 772-283-8800

Find the Part by Symptom

Start with what the door is doing. The table points you to the most common cause and the parts to inspect first.

What the door is doing Usual cause Parts to check
Daylight, drafts, water or dust getting past a closed door Weather seal that has cracked, hardened or torn. Brush seal with worn or missing bristles. EPDM weather seals, brush seal kits
Rolling door drags, takes more force to move, or tracks unevenly Debris in the bottom track, a seized caster bearing, or a worn wheel. Casters, wheels and axle assemblies, bearings
Grinding, squealing or clunking while the door moves Dry or failed bearings, a worn guide roller, or a loose hinge. Bearings, hinge assemblies
Bifold door lifts unevenly, sags at the fold, or binds partway Worn mast guide bearing, a failing hinge, or a frayed or stretched lift cable or strap. Mast guide bearings, bifold bearings, hinge assemblies, 1/4 in. galvanized lift cable. Call us about lift straps.
Door runs past its stop, stops short, or will not stop on its own Limit switch out of adjustment or failed. Bent or loose switch bracket. Rotary, snap action and Square D limit switches, mount brackets
Nothing happens when you press the button, or it works only sometimes Worn button or pendant, damaged power cord, or a tripped E-stop. Control pendant, power buttons and E-stops, SOOW cords
Power cord snags, sags or drags as a rolling door travels Broken or missing festoon trolleys. Festoon cable trolleys
Drive chain slips, jumps or runs loud Worn sprocket teeth or a stretched chain. Sprockets, master links
Door slams at the end of travel Missing or crushed bumper. Door bumpers
Motor hums, trips the breaker, or will not turn Motor, brake or operator fault. Call us. These are matched to your door by phone.
Hydraulic door drifts down, leaks fluid, or lifts slowly Cylinder, hose, valve or pump fault. Call us. Keep everyone clear of the door until it is secured.

Repair by Door Type

Rolling Hangar Door Repair

A bottom rolling door carries its full weight on its casters, so most problems show up as a door that is harder to push or that pulls to one side. Clear the bottom track first. Packed dirt, gravel and rust scale cause more dragging than failed parts do. If the track is clean and the door still drags, check each caster for a wheel that will not spin freely or that has play on its axle.

From there, look at the top guide rollers, then the drive. On powered doors, check the chain and sprockets for wear and the festoon trolleys that carry the power cord.

Bifold Hangar Door Repair

Bifold doors lift on cables or straps, which means the lifting parts are under load any time the door is off the ground. Watch the door through a full cycle from a safe distance. Uneven lift from side to side points to a cable or strap problem. A door that binds or chatters as it folds points to hinges or mast guide bearings.

Inspect cables for broken strands and flat spots, and straps for fraying at the edges. Replace them in sets so the door lifts evenly.

Hydraulic Hangar Door Repair

On a one-piece hydraulic door, the parts an owner can usually replace are the seals around the perimeter and the controls. Weather seals, brush seals, buttons and cords are all stocked for hydraulic doors.

Anything in the hydraulic circuit is different. Fluid on the floor, a door that creeps down, or slow and jerky lifting all need a qualified technician, and the parts need to be matched to your system. Call us for those.

Motors, Operators and Hydraulic Components

Motors, operators, cylinders, valves and pumps are not sold through the website. They have to match your door's weight, voltage, phase and mounting, and ordering the wrong one is an expensive mistake. Call and we will confirm the specs with you before anything ships.

Have this ready when you call:
Door type and size, the motor nameplate details (horsepower, voltage, phase), and a photo of the part.

Call 772-283-8800

What You Can Repair Yourself and When to Call a Technician

Usually owner-serviceable

  • Replacing weather seals and brush seals
  • Clearing and cleaning the bottom track
  • Greasing bearings and casters
  • Swapping a bumper, button or pendant with power locked out
  • Replacing festoon trolleys

Bring in a qualified technician

  • Lift cables, lift straps and anything else holding the door up
  • Hinges on a bifold or hydraulic door
  • Hydraulic cylinders, hoses, valves and pumps
  • Motor, brake and control panel wiring
  • Any door that has dropped, racked or come off its track

Safety first. Lock out power before working on any powered door. Never work under a raised bifold or hydraulic door unless it is mechanically supported. If you are not sure a repair is safe to do yourself, call a technician and let us supply the parts.

How to Identify the Part You Need

You do not need to know who built your door. Parts are matched by type and measurement, and we carry parts for doors from any manufacturer. Before you order or call, gather:

  • Door type: bifold, bottom rolling or hydraulic, and the opening width and height.
  • Photos: the failed part in place, plus a close-up of any stamped numbers or nameplate.
  • Measurements: wheel diameter, shaft or bore size, seal thickness and width, cable diameter.
  • Electrical details: voltage and phase for anything wired.

If the part is obsolete or was custom built for your door, send us the details. If we cannot find it, we will try to fabricate it. Send a part request.

Repair Parts by Industry

Hangar doors are not only on airfields. The same bifold, rolling and hydraulic doors close off boat storage, farm buildings, warehouses and home shops. Pick your industry to see the parts that fit how your door is used.

Repair and Maintenance Guides

Hangar Door Repair Questions

Do you send technicians out to repair hangar doors?

No. Hangar Door Parts supplies replacement parts and phone support. We help you or your technician identify the right part and ship it to you.

Can I get parts if I do not know who made my door?

Yes. Most parts are matched by door type and measurements, not by brand. Send photos and dimensions and we will match the part.

Why is my rolling hangar door hard to move?

Start with the bottom track. Debris is the most common cause. If the track is clear, check each caster for a wheel that will not spin freely, then check the bearings.

How do I know my hangar door seals need replacing?

Look for daylight around a closed door, rubber that has cracked or gone hard, and brush seals with bent or missing bristles. Water or dust inside after wind and rain is another sign.

Can you supply a motor or hydraulic part for my door?

Call us for motors, operators and hydraulic components. These are matched to your door by phone so the specs are confirmed before anything ships.

What if the part I need is no longer made?

Send us a detailed description, photos and measurements. If we cannot source the part, we will try to fabricate it.

Ready to get your door working again?
Shop parts by door type, or call and we will help you find the right one.

Shop All Parts